FixItFirst

The cycle's finished, you go to grab your laundry, and the door just won't budge. It's one of the more panic-inducing washer problems, especially if you've got clothes you need right now, but the causes are almost always straightforward, and there's a safe way to handle it even in the moment. 1. The door lock hasn't released yet (this is normal) Front-loading washers use a heat-activated door lock mechanism that sometimes takes a couple of minutes to cool down and release after the cycle ends, especially after a hot wash. Before assuming anything's wrong, just wait 2-3 minutes after the cycle finishes and try again. 2. There's still water in the drum Most washers won't unlock the door if there's standing water inside, as a safety measure. If your machine didn't drain properly (check our article on drainage issues if this is the case), the door staying locked is actually doing its job. Run a drain or spin cycle again, or manually drain the...

 You start the cycle, wait for that familiar sound of water rushing in, and... nothing. The drum just sits there, dry, while the machine seems to be running through its motions with no water in sight. It's an odd one because everything else about the machine seems fine — it's just not filling. Here's what's usually going on. 1. Water supply valves are closed or barely open This sounds almost too simple, but it's the most common cause by far. Check the hot and cold water valves behind the machine (usually small taps on the wall) and make sure they're fully open. It's especially common after moving the machine for cleaning and forgetting to fully reopen the valves afterward. 2. Kinked or blocked supply hoses If the valves are open but water still isn't coming through, check the supply hoses themselves for kinks or bends, especially if the machine's been pushed back against the wall recently. 3. Clogged inlet filters Most washing machines have sma...

 You start a load, walk away, and come back an hour later to find the machine sitting there, stuck on the exact same point in the cycle it was at when you left. No progress, no error beeping, just... stuck. It's a frustrating one because it doesn't always come with an obvious clue about what's wrong. Here's how to work through it. 1. The machine is waiting on something it needs Before assuming a fault, rule out the boring explanations first. Many washers pause and wait if the door isn't fully latched, if they're mid-way through detecting the load size, or if they're paused for an additive dispenser (fabric softener, bleach) to release at the right moment. Give it a few extra minutes before assuming it's actually stuck. 2. Door lock isn't engaging Front-loaders in particular won't move past certain points in the cycle unless the door lock sensor confirms the door is sealed. If something's blocking the door from closing fully — a stray sock...

 There's a specific kind of dread that comes with a washing machine that suddenly starts banging, grinding, or shaking like it's about to walk itself across the room. Before you assume the worst, know that loud noises are one of the most common washer complaints out there, and most causes are nowhere near as serious as they sound. Here's what's usually behind it, from the simplest fix to the ones that need a repair tech. 1. Unbalanced load This is the number one cause of loud banging or shaking, especially during the spin cycle. One heavy item — a comforter, a pair of sneakers, a single towel — thrown in alone will make the drum spin off-balance and slam against the housing. Stop the machine, redistribute the load evenly, and see if the noise goes away. 2. Machine isn't level Washing machines have adjustable feet for a reason: even a slight tilt amplifies vibration dramatically. Check by gently pushing each corner of the machine to see if it rocks. If it does, ...

 Finding a puddle under your washing machine is never a fun surprise, especially with water pooling that close to an electrical appliance. The good news is that leaks almost always come down to one of a handful of usual suspects, and most of them are a quick, free fix once you know where to look. Here are the 7 most common causes, starting with the easiest to check. 1. Door seal (gasket) is torn or dirty On front-loading machines, the rubber gasket around the door is the number one leak source by far. Gunk builds up in the folds over time, and small tears can develop after years of use. Run your hand around the entire seal, feeling for rips, and check for any spot where it's pulling away from the drum. 2. Overloading the machine Stuff the drum past its recommended capacity and water can splash right past the seal during the wash, simply because there's nowhere else for it to go. Try a smaller load next time and see if the leak disappears. 3. Too much detergent, or the wro...

Washing Machine Not Spinning? 8 Things to Check Before Calling a Repairman If your washing machine finishes its cycle but the drum doesn't spin, don't assume that the machine needs to be replaced. In many cases, the cause can be something simple that you can check yourself. Here are some of the most common reasons why a washing machine won't spin and what you can do about them. 1. The washing machine is overloaded One of the simplest reasons a washing machine may not spin is an unbalanced or overloaded drum. Heavy items such as towels, blankets and bedding can move to one side of the drum during the cycle. When this happens, the washing machine may stop the spin cycle to prevent excessive vibration. Try removing some of the clothes and spreading the remaining items evenly around the drum. Then run a spin cycle again. 2. The drain filter is blocked If there is still water inside the drum, the washing machine may refuse to start the spin cycle. A blocked pump filter...

 You walk into the laundry room and there it is — a puddle spreading out from under your Whirlpool washer. Your first instinct is probably to panic a little, especially with water this close to an electrical appliance. Take a breath: leaks are almost always traceable to one of a handful of spots, and most of them are a quick fix once you know where to look. Here's how to track it down, from the most common causes to the least. 1. Door seal (gasket) is torn or dirty On front-loading Whirlpool models, the rubber gasket around the door is the number one leak source. Over time it collects gunk in the folds, and small tears or gaps can develop from years of use. Run your hand around the entire seal, inside the folds, feeling for tears, and check for any spot where it's pulling away from the drum. A damaged gasket needs replacing, but a dirty one just needs a good clean with soap and water. 2. Overloading the machine If you're stuffing the drum past its recommended capacity, ...

There's nothing quite like opening your LG washer expecting clean laundry and instead finding a drum full of standing water. It's messy, it's frustrating, and it usually happens right when you're in a hurry. The good news? This is one of the most common issues LG owners run into, and most of the time it's an easy fix you can knock out yourself. Here's what's usually behind it, starting with the easiest checks first. 1. Clogged drain pump filter This is the number one cause, by far. LG front-loaders have a small access panel at the bottom front of the machine — usually behind a little flip-down door. Inside is a filter that traps coins, buttons, pet hair, tissues, you name it. Once it's packed full, water simply can't drain out. Pop it open (keep a towel and a shallow container nearby, because water will come out), pull the filter, and clean it out thoroughly. 2. Kinked or clogged drain hose If the filter's clear and you're still stuck, c...

 So your Samsung washer just finished its cycle and your clothes are still sitting in a puddle. Annoying, right? Before you start Googling repair shops near you, take a breath — this is one of the most common complaints with Samsung washers, and more often than not, it's something you can sort out yourself in under 20 minutes. Let's walk through the usual suspects, starting with the stuff that takes two minutes to check. 1. Unbalanced load This is, hands down, the number one reason a Samsung washer refuses to spin. These machines have built-in sensors that detect when the load is lopsided, and if it is, the washer just won't risk spinning — it'll either slow way down or skip the spin cycle entirely to protect itself. If you threw in one heavy item (a comforter, a pair of sneakers, a single towel), that's probably your culprit. Open the door, redistribute the load evenly, and restart just the spin cycle. 2. The lid or door isn't locking properly Samsung washe...